applications optiva ots-2 c-band rf fiber optic links features / benefts ? c-band uplink and downlink - eliminates the performance and cost penalty of block up/ down conversion ? low rin source laser - provides high- dynamic-range of >102 db hz 2/3 ? microprocessor-based transmitter control for laser bias, modulator bias & link gain - provides consistent high performance operation and allows for modulator low-bias operation and sfdr >102 db hz 2/3 ? snmp v.1 and rs-232 monitor & control interface - flexible user interface options ? compatible with emcores modular optiva platform - allows multiple format and frequency transport in a single chassis ? dwdm operation - increases transport capacity without increasing fber count the optiva ots-2 c-band transmitter and receiver are ideal to construct downlink 3.400 to 4.200 ghz and uplink 5.850 to 6.725 ghz transparent fber optic links for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. optiva satellite and microwave transmitters and receivers are snmp compliant. they can be housed in the same chassis and monitored by the same network management system (nms) as optiva hd video, audio, serial data, and usb extension / distribution cards to provide multiple format and frequency transport in a single fexible platform. system design the optiva platform includes a wide range fber optic transport products for satellite and microwave communications from 1 mhz to 40 ghz. these units can be used to construct transparent inter- and intra-facility links from 1 meter to >100 km for rf and microwave signal transport, antenna remoting, video transport, electronic warfare systems and other high-dynamic-range applications. optiva is a completely modular, hot-swappable platform. both 19 rack-mount and compact tabletop, or wall-mountable enclosures are available. the 3 ru 19 rack-mount, fan-cooled enclosures (model ot-cc-16 and ot-cc-16f) can support up to 16 insert cards and utilize two dual-redundant, hot-swappable, 100 or 200 watt power supplies. the 1 ru 19 rack-mount, fan-cooled enclosure (model: ot- cc-6-1u) can accommodate 6 insert cards and utilizes two hot-swappable 60 watt power supplies. compact one-slot (ot-dtcr-1), or two-slot (ot-dtcr-2) enclosures are also available that use an external wall-mount power supply. ? satcom c-band antenna signal distribution ? ground terminal & intra-facility links ? site diversity systems ? electronic warfare (ew) systems ? broadband delay line and signal processing systems t ransmitter receiver v ariable gain rf pr eamp out p l p r laser/modulator micr opr ocessor contro l -20 db rf t est point photodiode exter nally modulated t ransmitter rf in optical output +10 dbmo min optical input +11.8 dbmo max rf -20 db rf t est point optical pr eamp/rx micr opr ocessor contro l v ariable gain rf postamp block diagram satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
parameter min typical max units frequency range 3.400 5.850 - - 4.200 6.725 ghz ghz rf input power - - 5 * -15 ^ dbm wavelength - 1550 - nm optical output power 9 10 11 dbmo operating temperature range -10 - 50 c performance highlights *tx: rf amp 15 db gain, attenuation range 0 to 15 db ^tx: rf amp 35 db gain, attenuation range 0 to 15 db parameter symbol min max units operating temperature t op -20 60 c storage temperature t stg -40 85 c rf input s in na 5 * -15 ^ dbm stresses in excess of the absolute maximum ratings can cause permanent damage to the device. these are absolute stress ratings only. functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the datasheet. exposure to absolute maximum ratings for extended periods can adversely affect device reliability. *tx: rf amp 15 db gain ^tx: rf amp 35 db gain absolute maximum ratings enclosure options typical c-band downlink s21 frequency response typical c-band uplink s21 frequency response environmental specifcations parameter symbol min max units operating temperature t op -10 50 c operating humidity, maximum non-condensing -- -- 95% operating altitude, above sea level -- -- 6000 1828.8 ft m storage temperature t stg -40 70 c storage humidity, maximum non-condensing -- -- 95% -- storage altitude, above sea level -- -- 50,000 15,240 ft m optiva ots-2 c-band rf fiber optic links satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
transmitter & receiver optical characteristics parameter symbol condition min typical max units wavelength l - 1530 1550 1562 nm optical output power p l - 9 10 11 dbmo connector return loss - - 40 - - db optical connector type - sc/apc - - - - receiver optical input power p in - - - +10 dbmo receiver responsivity - - 0.7 - - a/w note: in order to prevent refection-induced distortion degradation, the laser should be connected to an optical cable having a return loss of at least 55 db for discrete refections and 30 db for distributed refections. c-band transmitter & receiver rf characteristics parameter condition min typical max units operational bandwidth - 3.400 5.850 - - 4.200 6.725 ghz ghz rf input impedance - - 50 - rf return loss - - - -15 db rf connectors sma female rf test point reference value, relative to rf input or rf output * - -18 -20 -22 db *test point performance beyond the stated frequency range is provided; only the test point reference value tolerance may increase beyond the above stated +/- 1 db dc power consumption - max module type input voltage (vdc) max current (@+70 c) transmitter +12 1 a receiver +12 750 ma optiva ots-2 c-band rf fiber optic links all modules are compliant with snmp v.1 supported through the optiva nms card (opv-ctlr-ic) network management satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
link performance - c-band uplink parameter symbol condition min typical max units rf bandwidth - - 5.850 - 6.725 ghz link gain (+0 dbmo rx optical input) *^ g g @ 5.850 ghz @ 6.725 ghz -2 -2 2 2 - - db db link gain (+10 dbmo rx optical input) *^ g g @ 5.850 ghz @ 6.725 ghz 18 18 22 22 - - db db noise figure (+0 dbmo rx optical input) ^ nf nf @ 5.850 ghz @ 6.725 ghz 12 12 - - - - db db noise figure (+10 dbmo rx optical input) ^ nf nf @ 5.850 ghz @ 6.725 ghz 7 7 - - - - db db input ip3 ^ iip3 iip3 @ 5.850 ghz @ 6.725 ghz - - -6 -5 - - dbm dbm spurious free dynamic range ^ sfdr sfdr @ 0 dbmo rx optical input @ +10 dbmo rx optical input 101 105 - - -- -- db-hz 2/3 db-hz 2/3 gain variation - - any 36 mhz any 500 mhz - - - - 0.5 1.5 db p-p db p-p *receiver rf output will change 2 db for each 1 db of rx optical input power level change ^performance based on ots-2t/s5 with rf amp gain of 35 db, ots-2r/s5 with rf amp gain of 15 db link performance - c-band downlink parameter symbol condition min typical max units rf bandwidth - - 3.400 - 4.200 ghz link gain (+0 dbmo rx optical input) *^ g g @ 3.400 ghz @ 4.200 ghz 0 0 4 4 - - db db link gain (+10 dbmo rx optical input) *^ g g @ 3.400 ghz @ 4.200 ghz 20 20 24 24 - - db db noise figure (+0 dbmo rx optical input) ^ nf nf @ 3.400 ghz @ 4.200 ghz 12 12 - - - - db db noise figure (+10 dbmo rx optical input) ^ nf nf @ 3.400 ghz @ 4.200 ghz 7 7 - - - - db db input ip3 ^ iip3 iip3 @ 3.400 ghz @ 4.200 ghz - - -6 -5 - - dbm dbm spurious free dynamic range ^ sfdr sfdr @ 0 dbmo rx optical input @ +10 dbmo rx optical input 101 105 - - - - db-hz 2/3 db-hz 2/3 gain variation - - any 36 mhz any 500 mhz - - - - 0.5 1.5 db db *receiver rf output will change 2 db for each 1 db of rx optical input power level change ^performance based on ots-2t/s5 with rf amp gain of 35 db, ots-2r/s5 with rf amp gain of 15 db optiva ots-2 c-band rf fiber optic links satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
transmitter ots-2t / s5- vvvv - ww -10- xx -12- yy - z ? when ordering replace vvvv with one of the c-band frequency options ? when ordering replace ww with one of the itu channel options ? when ordering replace xx with one of the optical connector options ? when ordering replace yy with one of the variable gain rf amplifer options ? when ordering replace z with one of the enclosure options rf connector c-band frequency options (ghz) vvvv itu channel options (thz / nm) ww optical power (dbmo) optical connector options xx optical output + rf test port (db) variable gain rf amplifer options (db) yy enclosure options z s5 = 50 sma 3442 = 3.400-4.200 ghz uplink 5867 = 5.850-6.725 ghz downlink standard: 00 = non-itu: 1520-1580 nm optional: 18 = 191.8 thz/1563.05 nm 19 = 191.9 thz/1562.23 nm 20 = 192 thz/1561.42 nm 21 = 192.1 thz/1560.61 nm 22 = 192.2 thz/1559.79 nm 23 = 192.3 thz/1558.98 nm 24 = 192.4 thz/1558.17 nm 25 = 192.5 thz/1557.36 nm 26 = 192.6 thz/1556.56 nm 27 = 192.7 thz/1555.75 nm 28 = 192.8 thz/1554.94 nm 29 = 192.9 thz/1554.13 nm 30 = 193 thz/1553.33 nm 31 = 193.1 thz/1552.52 nm 32 = 193.2 thz/1551.72 nm 33 = 193.3 thz/1550.92 nm 34 = 193.4 thz/1550.12 nm 35 = 193.5 thz/1549.32 nm 36 = 193.6 thz/1548.51 nm 37 = 193.7 thz/1547.72 nm 38 = 193.8 thz/1546.92 nm 39 = 193.9 thz/1546.12 nm 40 = 194 thz/1545.32 nm 41 = 194.1 thz/1544.53 nm 42 = 194.2 thz/1543.73 nm 43 = 194.3 thz/1542.94 nm 44 = 194.4 thz/1542.14 nm 45 = 194.5 thz/1541.35 nm 46 = 194.6 thz/1540.56 nm 47 = 194.7 thz/1539.77 nm 48 = 194.8 thz/1538.98 nm 49 = 194.9 thz/1538.19 nm 50 = 195 thz/1537.4 nm 51 = 195.1 thz/1536.61 nm 52 = 195.2 thz/1535.82 nm 53 = 195.3 thz/1535.04 nm 54 = 195.4 thz/1534.25 nm 55 = 195.5 thz/1533.46 nm 56 = 195.6 thz/1532.68 nm 57 = 195.7 thz/1531.9 nm 58 = 195.8 thz/1531.12 nm 59 = 195.9 thz/1530.33 nm 60 = 196 thz/1529.55 nm 61 = 196.1 thz/1528.77 nm 62 = 196.2 thz/1527.99 nm 10 = +10 optical output standard: sa = sc / apc optional: fa = fc / apc ea = e2000 / apc 1 = single optical output + 2 = -20 db test port 15 = 15 db 35 = 35 db 1 = optiva indoor rack-mount installation 2 = optiva outdoor minihub installation ordering information: transmitter optiva ots-2 c-band rf fiber optic links satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
receiver ots-2r / s5- vvvv -10- ww - xx -2- yy - z ? when ordering replace vvvv with one of the c-band frequency options ? when ordering replace ww with one of the optical connector options ? when ordering replace xx with one of the itu channel options ? when ordering replace yy with one of the variable gain rf amplifer options ? when ordering replace z with one of the enclosure options ordering information: receiver rf connector c-band frequency options (ghz) vvvv optical power (dbmo) optical connector options ww itu filter options for improved optical isolation in dwdm systems (thz / nm) xx test port (db) variable gain rf amplifer options (db) yy enclosure options z s5 = 50 sma 3442 = 3.400-4.200 ghz uplink 5867 = 5.850-6.725 ghz downlink 10 = +10 max optical input standard: sa = sc / apc optional: fa = fc / apc ea = e2000 / apc standard: 00 = no flter optional: 18 = 191.8 thz/1563.05 nm 19 = 191.9 thz/1562.23 nm 20 = 192 thz/1561.42 nm 21 = 192.1 thz/1560.61 nm 22 = 192.2 thz/1559.79 nm 23 = 192.3 thz/1558.98 nm 24 = 192.4 thz/1558.17 nm 25 = 192.5 thz/1557.36 nm 26 = 192.6 thz/1556.56 nm 27 = 192.7 thz/1555.75 nm 28 = 192.8 thz/1554.94 nm 29 = 192.9 thz/1554.13 nm 30 = 193 thz/1553.33 nm 31 = 193.1 thz/1552.52 nm 32 = 193.2 thz/1551.72 nm 33 = 193.3 thz/1550.92 nm 34 = 193.4 thz/1550.12 nm 35 = 193.5 thz/1549.32 nm 36 = 193.6 thz/1548.51 nm 37 = 193.7 thz/1547.72 nm 38 = 193.8 thz/1546.92 nm 39 = 193.9 thz/1546.12 nm 40 = 194 thz/1545.32 nm 41 = 194.1 thz/1544.53 nm 42 = 194.2 thz/1543.73 nm 43 = 194.3 thz/1542.94 nm 44 = 194.4 thz/1542.14 nm 45 = 194.5 thz/1541.35 nm 46 = 194.6 thz/1540.56 nm 47 = 194.7 thz/1539.77 nm 48 = 194.8 thz/1538.98 nm 49 = 194.9 thz/1538.19 nm 50 = 195 thz/1537.4 nm 51 = 195.1 thz/1536.61 nm 52 = 195.2 thz/1535.82 nm 53 = 195.3 thz/1535.04 nm 54 = 195.4 thz/1534.25 nm 55 = 195.5 thz/1533.46 nm 56 = 195.6 thz/1532.68 nm 57 = 195.7 thz/1531.9 nm 58 = 195.8 thz/1531.12 nm 59 = 195.9 thz/1530.33 nm 60 = 196 thz/1529.55 nm 61 = 196.1 thz/1528.77 nm 62 = 196.2 thz/1527.99 nm 2 = -20 db test port 15 = 15 db 35 = 35 db 1 = optiva indoor rack- mount installation 2 = optiva outdoor minihub installation optiva ots-2 c-band rf fiber optic links satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
each transmitter and receiver module occupies two slots in the emcore optiva chassis. mechanical confguration this product meets the appropriate standard in title 21 of the code of federal regulations (cfr). fda/cdrh class 1m laser product. all versions of this laser are class 1m laser product, tested according to iec 60825-1:2007 / en 60825-1:2007. an ad - ditional warning for class 1m laser products. for diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye loupes, magnifers, and microscopes) within a distance of 100 mm may pose an eye hazard. for collimated beams, this warning shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard. wavelength = 1.3/1.5 m. maximum power = 30 mw. *caution - use of controls or adjustments or performance of procedures other than those specifed herein may result in hazardous radiation exposure. *iec is a registered trademark of the international electrotechnical commision. invisible laser radia tion av oid direct exposure to beam w avelength: 1.5 m max. output: 50 mw class 1m laser product invisible laser radia tion is emitted from the end of fiber or connect or av oid direct exposure to beam do not view beam directly with optical instruments invisible laser radia tion emitted from end of fiber or connect or class 1m laser product iec 60825-1:2007 en 60825-1:2007 max output : 50 mw wa velength: 1.5 m (+ 1460 to 1620 nm) complies with 21 crf 1040.10 and 1040. 11 except for deviations pursuant to laser notice no. 50, dated june 24, 2007 g8760-073-001 re v. 3 laser safety optiva ots-2 c-band rf fiber optic links satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
|
